Wisconsin Motors Canada - Four Cylinder Engines For Sale

Wisconsin Engines & Long Blocks

Most of the engines listed below have been sold. It is time consuming to update these on a regular basis. Please contact us and let us know what it is you are looking for. We do have losts of new and rebuilt engines and cores in stock but this changes daily.

Model	Horizontal Shaft - Four Cylinder	Price
V465D with saw Posted 10-04-07	We have a complete Magnum Model 6585 LONG NOSE concrete saw for sale with approx. 650 hours on it. It comes with the humungous blade guards shown in the pictures and a couple of partially used blades for the guards. Engine starts with a flick of the switch, does not burn oil and the complete machine was well maintained by its present owner (whom we know well and we are familiar with how they maintain their equipment) The saw has been cleaned up and re-painted with new decals on it. The saw is located in Uxbridge, Ontario (near Toronto) If you require any further information or a freight price to your door (we use Old Dominion Freight Lines www.odfl.com) contact us. If someone is looking for a great running 65 hp engine and doesn't need the saw portion this is still a great buy at $7,000. REDUCED TO MOVE - $5,500 Canadian 10-04-07 CLICK ON PICS BELOW TO ENLARGE	$5,500 CAD (approx. $5,500 USD)
VE4D 21.5 hp @ 2400 rpm Like New	We have a customer who bought a skid steer loader that originally had a VH4D in it. The previous owner blew it up and replaced it with a VE4D. It is under powered and the new owner has re-installed the proper VH4D back into the machine. The VE4D is for sale as follows; Complete engine has approx 80 hours on it and comes with an oil bath air cleaner assembly, fixed flywheel screen, not a rotating screen like engines from a swather. There is no muffler,(it can be added for $75 Cdn) but comes with a new 6 volt battery. The electrical system is 6v positive ground however the existing starter is a heavy duty unit and can be run with a 12v battery. The crankshaft is the standard 1-7/16 keyed shaft is about 2" in length and enough to put a pulley or Lovejoy coupling on. Please deal directly with the customer and contact Karl at karlofkeswick@sympatico.ca. (Keswick, Ontario, about 30 minutes north of Toronto). He can arrange for shipping anywhere in North America and can quote you a price on this. If you are looking for reliable power (21.5 hp at 2400 rpm) this is an economically priced unit with big torque. For specs click here	$1,200 Canadian, $1,200 USD no exchange required OR MAKE OFFER
VH4D Spec # 465663	New 30 hp VH4D, Erickson Corp. spec, 4 cylinder (V-4) with horizontal 1-7/16" dia. CA71A36 keyed shaft, flywheel side of crankshaft has provisions for hand crank starting. There is enough keyed shaft to mount a Lovejoy style coupling or a pulley with split tapered bushing arrangement.W4-1770 style manifold L253L with L57 carb with inlet at fs. No air cleaner supplied but there is a 45o adaptor on carb with an o.d. of 1-3/4" to allow you to attach a hose going to a remotely mounted air cleaner assy ( not supplied). Also no muffler, outlet is at pto side at top of manifold. Crankcase face is drilled and tapped to accept a bell housing. Engine has an enclosed breather system (pipe on oil filler tube to intake manifold),comes with 12v Prestolite starter but no charging system 90 day warranty.	$4,500 no exchange required
VH4D Spec # 465703	New 30 hp VH4D, 4 cylinder (V-4) with horizontal 1-7/16" dia. CA71A36 keyed shaft, flywheel side of crankshaft has provisions for hand crank starting. There is enough keyed shaft to mount a Lovejoy style coupling or a pulley with split tapered bushing arrangement. Flywheel is machined with 6 holes drilled and tapped to allow installation of a stub shaft on the flywheel side of the engine and there is a 6" dia. hole in the non rotating flywheel screen. Manifold and carb is the same as spec 465663 above. Top mounted ssi distributor. No muffler, air cleaner or charging system 90 day warranty.	$4,500 no exchange required
VH4D Rebuilt engine	30 hp VH4D, 4 cylinder (V-4) with horizontal 1-7/16" dia. full length keyed shaft, 12v electric start and 30 amp charging system, engine mounted panel with ammeter, turn and lock speed control, choke control and switch, Prestolite points distributor ignition, dry type air cleaner assembly, crankcase is drilled and tapped to accept a hydraulic pump adaptor, top outlet exhaust (standard factory LD253 manifold) with WD86 direct mount muffler, 90 day warranty	$3,700 with exchange $4,100 w/o exchange
VH4D Spec # 448367	New replacement engine for Melroe Bobcat Model's 700 and 720. Side mount solid state distributor, less air cleaner and muffler (transfer over your old components). Flywheel side of crankshaft has provisions for hand cranking. Engine has standard L253 manifold with L63 carb. Muffler outlet at pto side of manifold, 2 studs to allow flange mounting of a muffler and pipe (not supplied). 12v starter installed but no charging system supplied. This engine drives off the flywheel side of the cs. The pto end does not have any crank protruding past the oil seal. carb inlet is at the fs of the engine. 90 day warranty.	$5,000 no exchange required
VH4D LB Assy Part # SB467403	New replacement long block assembly for a Melroe Bobcat Model's 630 and 730.For top mount distributor. Crankshaft at pto side sticks out about 7/8" from the face of the case with a 7/8" dia thread 12 threads per inch. 90 day warranty.	$3,500 no exchange required
VH4D LB Assy Spec # SB467403	New replacement long block assembly for a Melroe Bobcat Model's 630 and 730.For top mount distributor. Crankshaft at pto side sticks out about 7/8" from the face of the case with a 7/8" dia thread 12 threads per inch. Description of a WISCONSIN LONG BLOCK ASSEMBLY A Wisconsin long block is a low cost alternative to replacing the complete engine and is especially practical when all your external components are in good condition. A long block is manufactured by and supplied by the factory. Basically they make a standard engine production run and pull them off the line before they start attaching all the external components. This guarantees consistent quality. A long block assembly is made up of the following components; 1) crankcase, cylinder barrels and heads 2) front and rear main bearing plates 3) pistons, rings, crankshaft, camshaft, valves, guides, etc 4) all is assembled complete ready to transfer over your old components and they include all the gaskets you require to install your magneto or distributor drive, carb, fuel pump, intake and exhaust manifold, etc.	$3,500 no exchange required
VH4D with Gorman Rupp Pump UNIT IS SOLD	This unit was prepared for a customer who no longer needs/wants it. This is a completely rebuilt VH4D, not just some re-ring with fresh paint. This engine has been bored with new long skirt durable four ring pistons, new valves, new valve guides, new main bearings, crank turned and installed properly using factory specs. for lash, new rod bearings, all new gaskets and seals, new fuel pump, electric start or hand crank, easy to start even with hand crank, magneto ignition, new ring gear, carb. kit, cylinder fins and manifold treated with high heat paint, properly timed and ready to install. Pump model 14A2-VH4D S/G, can send PDF file with all pump specs., just email. All Genuine Wisconsin parts. Contact us Click pic to enlarge	$3,000 no exchange required
W4-1770 Rebuilt Target Saw Replacement and others	Target Concrete Saw Spec 35.0 hp W4-1770, 4 cylinder (V-4) with a horizontal 1-7/16" dia. keyed crankshaft extending 4.5" from the face of the case. This engine comes less air cleaner assembly and muffler. You transfer over your old ones.It has a new top mounted solid state distributor distributor and a 30 amp flywheel alternator. 90 day warranty	$3,500 with exchange $4,000 w/o exchange
VG4D	We have a good running VG4D in excellent conndition with low hours on it. Comes with the standard 1-3/4" diameter keyed shaft extending about 4" long from the oil seal and flywheel alternator charging system. The tinwork is not rusted or dented, engine has been test run and painted. You use your old air cleaner and muffler.	$2,000 w/o exchange
VG4D Spec # 464120	New 37 hp VG4D, 4 cylinder (V-4) with horizontal 1-1/2" dia. full length threaded pump shaft (CA69C83), 12v electric start and charging system, engine mounted panel with ammeter, turn and lock speed control, choke control and switch, SSI side mount distributor, side mount oil bath air cleaner assembly, top outlet exhaust on pto side of engine with pancake muffler pointing straight up, flywheel side of crankshaft has provisions for hand crank starting, low oil pressure safety switch wired into ssi, mechanical fuel pump, crankcase face drilled and tapped to accept bell housing, 90 day warranty	$5,500 no exchange required
V465D New LB Assy	These are factory new long block assemblies 65.9 hp, 4 cylinder OHV, (V-4) with horizontal 2.0" dia. full length keyed shaft, full factory warranty Description of a WISCONSIN LONG BLOCK ASSEMBLY A Wisconsin long block is a low cost alternative to replacing the complete engine and is especially practical when all your external components are in good condition. A long block is manufactured by and supplied by the factory. Basically they make a standard engine production run and pull them off the line before they start attaching all the external components. This guarantees consistent quality. A long block assembly is made up of the following components; 1) crankcase, cylinder barrels and heads 2) front and rear main bearing plates 3) pistons, rings, crankshaft, camshaft, valves, guides, etc 4) all is assembled complete ready to transfer over your old components and they include all the gaskets you require to install your magneto or distributor drive, carb, fuel pump, intake and exhaust manifold, etc. Shipping weight is 432 lbs, shipped on a pallet with heavy corrugated carton strapped over it, shipping dimensions is 33" x 33" x 36".	$5,000 no exchange required
V465D Rebuilt Complete Engine	Special Pricing for Concrete Saws or Duct Cleaning Trucks 65.9 hp, 4 cylinder OHV, (V-4) with horizontal 2.0" diameter keyed shaft, 12v electric start with external belt driven alternator, engine mounted panel with ammeter, oil pressure gauge, turn and lock speed control, choke control and switch, top outlet exhaust (std factory manifold) with WD111A standard direct mount muffler or WD76 Horizontal mount, specify which, 90 day warranty	$5,000 with exchange $5,500 w/o exchange
V465D New Complete Engines	Special Pricing for Concrete Saws and Duct Cleaning Trucks Click duct truck pics to enlarge 65.9 hp, 4 cylinder OHV, (V-4) with horizontal 2.0" dia. full length keyed shaft, 12v electric start with 12v charging system, (std factory manifold) with WD111A standard direct mount muffler or WD76 horizontal mount, specify which, one year factory warranty	$6,900 no exchange required
V465D Rebuilt c/w clutch pto	65.9 hp, 4 cylinder OHV, (V-4) with clutch power take off, 12v electric start with external belt driven alternator, engine mounted panel with ammeter, oil pressure gauge, turn and lock speed control, choke control and switch, top outlet exhaust (std factory manifold) with WD111A standard direct mount muffler or WD76 Horizontal mount, specify which, 90 day warranty	Price on Request

cis - cast iron sleeve es - 12 electric starter and charging system los - low oil shutdown safety
ohc - overhead camshaft ohv - overhead valve rs - recoil starter sv - side valve (L head)

If we don't have your particular spec we can always modify any of the engines listed above to accommodate your own unique application. This includes changing flywheels and charging systems, crankshafts, and manifolds, etc. Contact us regarding your specific requirements.

Back

| home | about us | contact us |