| home | contact us |
Copyright
(2003) WMC Last updated 04-20-07| ENGINE MODEL | V465D |
| Current engine model ? | still in production as of April 2007 |
| # of cylinders | 4 |
| Cylinder configuration | V-4 |
| Head / valve style | overhead valve |
| Standard Bore Size |
3.749" - 3.748" (95 mm), if worn .005"
over standard size, re-bore, hone and fit with oversize pistons and rings |
| Stroke | 4.00" (102 mm) |
| Displacement | 177 cubic inches (2901 cc) |
| Maximum Horsepower @ RPM | 65.9 @ 3000 |
| Horsepower @ 2400 RPM | 60 |
| Horsepower @ 2000 RPM | 52 |
| Weight - Ibs. (kg) | 530 Ibs. ( 241 kg) |
| Maximum Ft. Ibs, Torques @ RPM | 139 @ 1800 |
| Dimensions - Lx W x H | 34" x 28" x 36" |
| Maintenance Information | |
| Air cleaner, check and clean or replace |
oil bath, every 4-8 hours depending on working environment, dry type change only when restriction indicator advises you to |
| Oil level, check | every 4 - 8 hours |
| Oil Change | every 50 hours |
| Oil type, must meet or exceed API Service specification SE / CC |
-20oF to +32oF use 5w20, 5w30 or 10w, or 0of to 95oF use 10w30, 10w40, 15w40, 15w50, or 60oF to 120oF use 20w40, 20w50, 40w |
| Gasoline | regular grade gasoline only, (87 octane minimum) |
| Clearance & Tolerances | |
| Piston skirt to bore clearance | .0025 - .003 cam ground piston |
| Crankpin diameter | 2.1233 - 2.1238 |
| Connecting rod to crankpin clearance | .0005 - .0018 shell bearing to crankpin clearance, vertical |
| Center bearing Shell (V465D only) | .0013 - .0038 |
| Valve tappet clearance - cold - inlet | .008 |
| Valve tappet clearance - cold - exhaust | .014 |
| Valve face and valve seat angle | 45o |
| Valve stem to guide clearance | .002" - .004", when clearance becomes over .002" over the high limit replace the guide(s) |
| Piston pin to piston | .0000" - .0008" tight |
| Piston pin to connecting rod | .0005" - .001" |
| Crankshaft end play | .002" - .005" cold |
| Bolt Torques - Foot Ibs. | |
| Connecting rod | 28 - 32 |
| Cylinder block / center main to crankcase |
center bearing hanger 74 - 76, prior to ser # 6089642 is 60, cap 32 - 35 |
| Cylinder head | alternate in three steps, 8 - 10, 18 - 20, 27 - 30 |
| Engine base | 8 - 11 |
| Gear Cover | 16 - 18 |
| Manifold | Upper to lower 13 - 15, to cylinder head 23 - 25 |
| Main bearing plate | 28 - 32 |
| Spark plug | 20 - 22 |
| Flywheel | 95 - 110 |
| Rope pulley | not applicable |
| Miscellaneous | |
| Crankcase oil capacity | 6 quarts plus 1 additional quart if replacing the filter |
| Running spark advance | 23o, run engine to 2000 rpm or higher |
| Breaker point gap | distributor 020", magneto .015" |
| Spark plug gap | .030" gasoline, .018" LPG |
| Maximum operating rpm | 3000 |
Copyright
(2003) WMC Last updated 04-20-07